Chapter 95 Opinions of the Leading Group for the Introduction of New Technologies
The "Three Automobile Preparatory Group" wants to buy General Motors' technology, but they want a joint venture.
The gap between the two sides' ideas is a bit big, and this week's negotiations are destined to be fruitless.
However, the First Ministry of Machinery also wrote a special report and sent it to the "New Technology Introduction Leading Group" under the Government Affairs Council for review.
The level of this leading group is relatively high, so major domestic technology introduction projects need to be reported specifically to them.
A big project like "Three Automotive Vehicles" is naturally not a problem.
After the elder in charge of this technical group saw the report, he felt that this matter was very important, so he signed his opinion and asked higher-level leaders for approval.
Finally, the chief engineer personally approved that "the joint venture can be done" and later gave the instruction that "the joint venture for cars can be done".
It’s just that although there is this review, if it is implemented, the people below have no idea.
It is impossible for the people from General Motors to stay in China for such a long time. In the end, this negotiation ended without any problem.
Of course, for both parties, this negotiation is not fruitless.
General Motors obtained the appearance design drawings of the new model from Jiang Hui. China knew that it could engage in a joint venture in the future. This incident directly affected Shouqi Jeep's negotiations.
Even the formation of joint ventures in China's automobile industry in the future is related to the review promoted by the "New Technology Introduction Leading Group" this time.
But these are all things for later.
For Jiang Hui, at this time he was explaining the cause and effect of the matter to Zhu Jiansheng.
"I was just on a business trip to FAW. I didn't expect so many things to happen."
"However, selling the appearance of a new model for $100,000 is still too sensitive, so you still have to pay a little attention. ”
Zhu Jiansheng was sent down and suffered a lot of losses.
Now, naturally, Jiang Hui is afraid of falling into the pit.
“Dad, don’t worry, I know what I know.”
"By the way, the first phase of the design work of the new BJ212 has basically come to an end. The next phase is for each supporting factory to start producing prototypes."
"I think this is also important for the Vehicle Engineering Department of our school. A good learning opportunity.”
“The parts designed on paper will inevitably have some unreasonable parts.”
“For example, the accuracy in some places is not necessary. High, the tolerance settings in some places are unreasonable.”
“These details are easily overlooked during design, but they are easily exposed during production.”
"I think we can involve teachers and students in the department in this project, and there may be unexpected gains."
Jiang Hui quickly shifted the topic to the new BJ212, which is the capital industry The bond of cooperation between the college and the Capital Automobile Manufacturing Plant during this period.
At the same time, this project is also a good opportunity to demonstrate and enhance the strength of the Vehicle Engineering Department of Capital Institute of Technology.
Jiang Hui plans to promote his father-in-law's position step by step in the future, so there are some opportunities that he cannot miss.
The strength and influence of the school's Vehicle Engineering Department can continue to expand in the hands of Zhu Jiansheng, and his influence in the school will also continue to rise.
It is not impossible to become a principal in the future, and it is even normal to move from school to serve in a ministry.
My mother-in-law’s family is a member of the system, and my father-in-law is also a person with some background.
If you push yourself, anything is possible.
In China, if you want to build your own automobile factory in the 1980s and 1990s, it will definitely not work without support. In fact, no matter in any era, the relationship behind a large automobile factory is relatively complicated.
"We are already cooperating with the Capital Gear Factory, the Capital Internal Combustion Engine Factory and the Capital Automotive Accessories Factory. I have also been communicating with them in the past few days."
"It's just right to share our theories with them. Let’s combine their practices with each other.”
Zhu Jiansheng is naturally aware of the benefits behind Jiang Hui’s proposal and is ready to actively promote it.
“Didn’t everyone discuss ‘Practice is the only criterion for testing truth’ some time ago?”
“I think you can elevate the significance of this action by then. , you can even find a way to get some newspapers to report it.”
Jiang Hui "follows the guidance" and hopes that Zhu Jiansheng will not just immerse himself in work, but also look up and see the way forward.
Otherwise, even if you work very hard and make great contributions, you often won’t get promoted.
In the workplace, especially in state-owned enterprises, this point needs special attention.
"Okay, I will arrange this matter."
"I have time to go home for dinner on the weekend."
Zhu Jiansheng was not stupid, so he naturally felt the "educational" meaning of his son-in-law's words, and his face was a bit confused.
Fortunately, he also knows that what Jiang Hui said makes sense, so he will definitely do the hard work he needs to do.
After taking care of his father-in-law, Jiang Hui continued to go back to the office to review the drawings of various parts of the new BJ212.
For the automotive industry, it is a very critical node to formally find supporting manufacturers with drawings to open molds and make parts.
OEMs need to formally issue written instructions to clearly indicate which version of the drawings to use to guide production.
If the drawings are wrong or the wrong drawings are used, the mold may be scrapped.
At that time, not only the money for mold production will be wasted, but also the large schedule of model development may be affected.
It stands to reason that Chen Qilai must ultimately be responsible for this review, but everyone knows what the design of the new BJ212 is.
Before Chen Qi and Lu Jianqiang sign all the drawings, there will be a confirmation step with Jiang Hui’s signature.
This is a novel thing witnessed by the technical staff of various supporting factories in the capital.
Everyone has a new understanding of Jiang Hui's position within the Capital Automobile Manufacturing Plant.
Invisibly, Jiang Hui's popularity in the capital's automobile industry has also been further improved.
What people who engage in technology admire the most are those whose technical capabilities are much stronger than themselves.
"Master, Director Zheng called you to come to his office."
Just when Jiang Hui took a sip of water from the enamel cup and was about to take a rest, Chen Chenxing answered He made a call and then came over to tell Jiang Hui that the factory director was looking for him.
This made Jiang Hui feel a little strange.
Under normal circumstances, the leader in the factory, Chen Qi, the chief engineer, would come to him directly. The factory director Zheng Haiming rarely asked him to go directly to his office.
Is it possible that something went wrong with the cooperation with General Motors?
With a trace of doubt, Jiang Hui walked towards the factory director's office holding a notebook and a pen in the upper left pocket of his work clothes.
(End of this chapter)